Ryobi AP1301 Betreibershandbuch PDF herunterladen (Seite 4)

SPECIFIC SAFETY RULES

GENERAL SAFETY RULES

 INSPECT TOOL CORDS PERIODICALLY. If dam-

aged, have repaired by a qualified service technician at

an authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 GROUND ALL TOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole

electrical receptacle.

 CHECK WITH A QUALIFIED ELECTRICIAN or service

personnel if the grounding instructions are not completely

understood or if in doubt as to whether the tool is properly

grounded.

 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire

extension cords that have 3-prong grounding plugs and

3-pole receptacles that accept the tool’s plug.

 DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 NEVER TOUCH BLADE or other moving parts during

use.

 NEVER START A TOOL WHEN ANY ROTATING COM-

PONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed

in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury.

Instructions for safe use of accessories are included

with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure blade is

tight and not making contact with tool or workpiece

before connecting to power supply.

 NEVER PERFORM THE PLANING OPERATION with

the cutter head or cutter guard removed.

 NEVER MAKE A PLANING CUT deeper than 1/8 in.

 DO NOT PLANE MATERIAL shorter than 14 in. or

narrower than 3/4 in.

 MAINTAIN THE PROPER RELATIONSHIP between the

infeed and outfeed surfaces and the cutter head blade

path.

 SUPPORT THE WORKPIECE ADEQUATELY at all

times during operation; maintain control of the work at

all times.

 NEVER FEED THE WORK from the rear of the planer.

 DO NOT ATTEMPT TO PERFORM an abnormal or little

used operation without the use of sturdy and adequate

jigs, fixtures, stops, and the like.

 NEVER plane more than one piece at a time. DO NOT

PLANE more than one workpiece on the planer table at

a time.

 BEFORE STARTING UP, recheck to make certain all

holding screws are tight.

 STOP THE MACHINE and recheck the hex head

bolts and blades for tightness after about 50 hours of

operation.

 DO NOT FORCE FEED THE WORKPIECE through the

machine. Let the planer apply the proper feed rate.

 CHECK THE FEED ROLLERS occasionally to be

sure there are no chips or sawdust between any

components.

 PLANE ONLY SOUND LUMBER; there should be no

loose knots and as few tight knots as possible. Make sure

the workpiece is free from nails, screws, stones, or other

foreign objects that could break or chip the blades.

 NEVER STAND DIRECTLY IN LINE with either the infeed

or outfeed sides. Stand off to one side.

 MAKE SURE THE BLADES ARE ATTACHED as

described in the operation section. The blades are sharp

and can easily cut your hand. Use caution in handling the

blades and cutter head guard.

1 2 3 4 5 6 7 8 9 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Ryobi AP1301 Betreibershandbuch Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Elektrische Planer Ryobi AP1301