Ryobi DP120 Bedienungsanleitung PDF herunterladen

THANK YOU FOR BUYING A RYOBI BENCHTOP DRILL PRESS.

Your new Drill Press has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation,

and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

CAUTION: Carefully read through this entire operator's manual before using your new machine.

Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your machine properly and only for

what it is intended, you will enjoy years of safe, reliable service.

Please fill out and return the Warranty Registration Card so we can be of future service to you.

Thank you again for buying Ryobi tools.

OPERATOR’S MANUAL

12 in. (305 mm) DRILL PRESS

MODEL DP120

SAVE THIS MANUAL FOR FUTURE REFERENCE

1 2 3 4 5 6 ... 17 18

Inhaltsverzeichnis

Seite 1 - MODEL DP120

1THANK YOU FOR BUYING A RYOBI BENCHTOP DRILL PRESS.Your new Drill Press has been engineered and manufactured to Ryobi's high standards for depend

Seite 2 - PRODUCT SPECIFICATIONS

10ASSEMBLYWARNING:Do not connect to power supply until assembly is complete.Failure to comply could result in accidental starting andpossible serious

Seite 3 - RULES FOR SAFE OPERATION

11ASSEMBLYINSTALLING THE IDLER PULLEYSee Figures 7 and 8. Place idler pulley in the center hole in the head assembly.Fit one belt over the spindle pu

Seite 4

12ADJUSTMENTSFig. 11TABLE ADJUSTMENTHANDLETABLE LOCKHANDLE00102030401020304012DrlliPressONWARNING:Before performing any adjustment, make sure the dril

Seite 5

1312DrlliPressONREMOVETO LOCKADJUSTMENTSFig. 14BELT TENSIONLEVERCHANGING SPEEDSSee Figure 14.WARNING:Before performing any adjustment, make sure the d

Seite 6 - ELECTRICAL

14INSTALLING BITSSee Figure 16. Unplug your drill press. Open or close the chuck jaws to a point where the openingis slightly larger than the drill

Seite 7 - UNPACKING

15WARNING:When servicing use only identical Ryobi replacementparts. Use of any other parts may create a hazard or causeproduct damage.WARNING:To avoid

Seite 8 - LOOSE PARTS

16Problem Possible Cause SolutionNoisy operationBit burns or smokesExcessive drill runout or wobbleDrill bit binds in workpieceWorkpiece support loose

Seite 9 - FEATURES

17NOTESNOTES

Seite 10 - WARNING:

983000-040 12-02RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road Anderson, SC 29625Post Office Box 1207 Anderson SC 29622-1207Phone 1-800-525-2579w

Seite 11 - ASSEMBLY

2Chuck 1/2 in. (13 mm)No Load Speed 280 - 3000 RPMSwing 12 in. (305 mm)Spindle Travel 3-1/4 in. (82 mm)Input 120V AC, 60Hz, 5 ampsNet Weight 84 lbs (3

Seite 12

3RULES FOR SAFE OPERATIONSafe operation of this power tool requires that you read andunderstand this operator's manual and all labels affixed tot

Seite 13 - OPERATION

4 ALWAYS TURN SWITCH OFF before disconnecting it toavoid accidental starting. ALL REPAIRS, WHETHER ELECTRICAL ORMECHANICAL, should be made at a Ryo

Seite 14

5RULES FOR SAFE OPERATIONThe purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations with

Seite 15 - MAINTENANCE

6ELECTRICALEXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the tool's plug.W

Seite 16 - TROUBLE SHOOTING

7GLOSSARY OF TERMSFeed HandlesThree handles attached to the quill which allow the operatorto lower the chuck and bit during a drilling operation.Motor

Seite 17

8Fig. 2 Spindle Chuck Tool Chuck Key Chuck Housing Knob and Screw Hex Bolts, M10 x 25 (4) Hex Wrench Table Adjustment Handle Operator’s Manua

Seite 18 - Model DP120

9FEATURESFig. 3KNOW YOUR DRILL PRESSSee Figure 3.Before attempting to use your drill press, familiarize your-self with all the operating and safety re