Ryobi RY43006 Betreibershandbuch

SAVE THIS MANUAL FOR FUTURE REFERENCEYour chain saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation

10Bar Tip GuardAn attachment that may be provided on the end of the guide bar to prevent the chain at the end of the guide bar from contacti

11FEATURESFig. 5PRODUCT SPECIFICATIONSBar Length... 18 in.Chain Type ...

12ASSEMBLYUNPACKINGThis product has been shipped completely assembled.n Carefully remove the tool and any accessories from the box. Make sure that al

13OPERATIONAUTOMATIC CHAIN OIL SYSTEMSee Figure 6. NOTE: Chain saw comes from the factory with no bar and chain oil added.n Use Power Care Bar an

14Fig. 8SWITCH LOCKSWITCH TRIGGERWARNING:Keep body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line.ST

15n Maintain a proper grip on the saw whenever the unit is running. The fingers should encircle the handle and the thumb is wrapped under the handleb

16Fig. 12PROPER CUTTING STANCESee Figure 12.n Weight should be balanced with both feet on solid ground.n Keep left arm with elbow locked in

17WARNING:If the tree starts to fall in the wrong direction, or if the saw gets caught or hung up during the fall, leave the saw and save yourself!n

18n Felling Backcut. The backcut is always made level and horizontal, and at a minimum of 2 in. above the horizontal cut of the notch. See Figures 14

19BUCKING LOGS UNDER STRESSSee Figures 19 - 20.When the log is supported along its entire length, it should be cut from the top or overbucking.When th

2n Introduction ...

20LIMBINGSee Figure 21.Limbing is removing branches from a fallen tree. n Work slowly, keeping both hands on the chain saw with a firm grip. Always m

21ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

22REPLACING BAR AND CHAIN See Figures 27 - 31.WARNING:Before performing any maintenance, make sure the tool is unplugged from the power supply. Failur

23n Reinstall the chain cover assembly, bushing and guide bar nut. Tighten the guide bar nut finger tight only. The bar must be free to move for tens

24CHAIN MAINTENANCESee Figures 32 - 33.Fig. 34Fig. 33CHECK FOR WEAR OR DAMAGEUse only 3/8 in. pitch skip tooth/low-kickback(62 drivelink) chain

25TOP PLATE FILING ANGLESee Figure 36.n CORRECT 30° - File holders are marked with guide marks to align file properly to produce correct top plate an

26Use a Flat File and a Depth Gauge Jointer to lower all gauges uniformly. Depth gauge jointers are available in .020 in. to .035 in. Use a .025 in. d

27SAFE-T-TIP® NOSE GUARD MAINTENANCESee Figures 42 - 43.Tighten the mounting screw of the nose guard as instructed below. These are specially hardened

28PROBLEM CAUSE SOLUTIONIF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTAC

29NOTES

3GENERAL SAFETY RULESREAD ALL INSTRUCTIONSBASIC SAFETY PRECAUTIONSn Do not start cutting until you have a clear work area, se-cure footing, and a pla

30RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Post Office Box 1207, Anderson, SC 29622-1207Phone 1-800-860-4050www.ryobitools.c

4GENERAL SAFETY RULESn Avoid body contact with grounded surfaces such as metal pipes and wire fences. There is an increased risk of electric shock if

5GENERAL SAFETY RULESKICKBACKSee Figures 1 - 2.WARNING:Kickback may occur when the moving chain contacts an object at the upper portion of the tip of

6GENERAL SAFETY RULESUNDERSTANDING YOUR CHAIN SAW SAFETY DEVICESSee Figure 4.SAFE-T-TIP® ANTI-KICKBACK NOSE GUARDThe SAFE-T-TIP® prevents rotationa

7 V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power

8SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

9EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h